Monkey fists don't work, or get stuck if they do

In the Czech Republic, there is amazing climbing on sandstone that isn't really held together well. Climbing protection like nuts or cams can damage the rock and there are very few bolts or "rings" to clip too. It has been a tradition there and is the actual rule, that you can only place textile protection. Tie knots in ropes and webbing and wedge them in like nuts or hexes. But does it actually hold a fall??? Thank you Jenny Fischer for narrating this episode and explaining where and why the rules exist, how it isn't ideal to be whipping on them, and how they can get stuck. OUR TESTS We tested overhands, double overhands, figure 8s and monkey fists wedged in our adjustable crack jib with granite slabs inside. This was in the drop tower and slow pull slacksnap machine to see if we got wildly different results, and the slow pull machine is easier to get a camera to show what's happening inside the crack. DON'T take these numbers as gospel. this was backyard science and the jib was flexing and the load cell app may not have been fast enough since it isn't the full 1280hz like the LineScale3 device itself is. It also really depended how constricted we made the crack. HOW they broke, got stuck or slipped out is way more interesting than the number itself and I encourage you to watch the video to see that. Timestamps will help you skip around. SO WHAT KNOT TO DO - Test Summary 1" webbing tend to not slip as easily and the loop didn't break until 7-10kN. The surface area is pretty good as friction plays a big role, but also probably because we could pinch the jib pretty tight below it. The 10mm knots almost all came out because the tightest the bottom of the crack can be is 10mm but one held 8kn which would hold a typical lead fall. Roll your dice. Paracord isn't strong enough at 3.5kN and only held when a rock was inside the monkey fists which you can't use. 6mm is barley good enough because when it did hold we would get around 6kN. Our slow pull 8mm monkey fist was impressive at 25kN but it slipped in the drop tests. How KNOT to Test Many people wonder why we do certain things in our test. You can see in the video we started with a 90lb dummy named Decker. We can move him around easy and it's more entertaining to see a dummy than steel weights but as you can see, that didn't work out. We aren't trying to see the force if A, B or C is done, we are trying to find out the breaking strength of each of these tests, so steel weights it was. We only do 2x 75lbs for a 150lb "dummy" because we just need to break the gear and really heavy weights free falling on only 9" of rubber gets complicated fast. When we use a "static" rope on the samples, it is too stretchy, believe it or not, to break most of the stronger gear 8kn and up. We have to go with more static or more weight so we chose a more static item - an industrial sling. It holds up to abrasion well and is plenty strong enough. Most ropes break around 16-20kn in a figure 8 so even if we went with more weight, ropes are quite limited. Load cells have to be FAST if using a STATIC attachment. The pro itself stretches enough that 1280hz, or 1280 readings per second, is probably super fast enough, though we will be testing this with a 10,000hz load cell to find out how short our peak force is soon. The app however is only able to feed at 40hz and the first few samples was only the app's number until we discovered that. Based on the numbers we got, it was super close enough because HOW this stuff broke or slipped was more interesting than the actual number itself. I think it's super helpful to know the flaws in any test because most testing has some flaws in it. If a polished graph is put on instagram or in an article, it is a mess with lipstick on it. We want so badly for a single number to explain everything and that is the problem with even MBS or minimum breaking strength, a number that has all variables removed so sterile that it doesn't even represent reality anymore. Reality is messy and that's ok. Understand your gear holistically and don't lean on 1 number to explain the entire story. Another Test The most referred to testing regarding textile passive pro is this ARTICLE by Jörg Brutscher from a 1997 test where they used a clamp and pulled various knots to see if they would slip or break. We found that our knots would only stay if the constriction was 1 diameter wide (pinching the rope) but they found with the figure 8, you could go up to twice the diameter of the rope. My rock jib is laughable because you can see it literally flexing on the drop tower, but this is also not very realistic in that friction plays a huge role in how these knots do. Their jib doesn't replicated a realistic scenario very well as it doesn't consider friction at all. Their machine only went up to 10kn. On their graph, you can see 8-10kN is "hard fall" which we could only achieve 8kn with TANNER who is 290lbs and his grigri was bolted to the wall. You would have to be doing something gnarly with someone heavy to get above 6kn. If trad gear is holding above 8kn, it's super good enough. In 2010, they tested knots in real rock which is pretty cool. The PDF shows their testing set up. They tested a figure 8 knot with two strands in an 11-13mm constriction. They hung a 50kg "belayer" and I believe the weight they dropped was also 50kg. It's a bit hard with google translate to see exactly the results but the thinner slings slipped and the bigger slings held. They got anywhere from 3kN up to 9kN on their tests. The rock got damaged and this is why I can't make a youtube video in 2022 in real rock on a real climb that I can drive my car right up to so I can bring 50kg weights to test. I know how much work this is and they get big kuddos for putting all this together. No test is perfect for an absolute real life scenario if the goal is destruction. There are many flaws in my testing as I try to perfect fake cracks and sustainable drop tests and there are many flaws in this testing. Take each data set as a piece to a bigger puzzle to understand this type of gear better. The Rules Are Knotty You can see the rules that state you must not use metal protection in the Czech Republic and also on the rocks in Saxon Switzerland . You also can't top rope these climbs as the rope rubbing the rock will damage the rock. Textile-only protection is intended not to damage the rock but if the gear is weighted, AND HOLDS, then it gets stuck. This leaves permanent plastic trash stuck in the rock for a very long time. Bolting everything could be an eye sore and a slippery slope to making more of an impact and more traffic to otherwise routes that wouldn't get climbed, but are bolts really uglier than hanging tat? Climber impact has left groves like this on top of the routes. You can see more worn away spots in this VIDEO . Monkey Fists In an effort to keep this 25 break test episode from getting too long, and that we are not experts in tying monkey fists, here is an ANIMATED KNOT VIDEO but we kept both tails out for a loop. You can tie it around a rock but that isn't street legal for the areas you would use it, you can tie around a smaller monkey fist that is pre-tensioned, or you can just do it with nothing in the middle. Another Option? Soft shackles technically are textiles, but if pretensioned, can get as hard as a rock. Diamond knots can have long tails coming out of the head for easy(er) removal. Button knots are bigger for the stem size. We did not test this with real rock but we did test this in our previous episode, and without friction and enough pressure also deformed and slipped out regardless of the constriction. However it was at 18kN or above which is technically as strong as your climbing rope. Check it out here.